How To Put Blade In Box Cutter

How To Replace A Utility Box Cutter Pocketknife Blade

The box cutter, or utility pocketknife, is an excellent tool establish in almost every warehouse. Designed with a small blade, these knives have the ability to quickly cut cardboard boxes open, remove packing record and other wrappings used in freight transit. Due to the corruption box cutters take, they are oft made from very hard plastic or metal.

Many warehouse employees view utility knives as throwaway items. Every bit shortly equally the blades wear out warehouse workers will typically begin looking for a new one. Fortunately, you're visitor does not need to waste money repeatedly buying new box cutters every week. A simple remedy is just to supersede the blade. And the all-time part? They normally come with extras!

Opening The Utility Pocketknife

The commencement step when replacing a box cutter blade is to figure out how it opens. In our example, nosotros but demand to use a Phillips head screwdriver and remove one spiral from the side. After removing the spiral you can merely pop the height off which splits the knife in half.

Identifying Components

There are really only 5 components to our utility pocketknife. The handle, the screw, the blade, the blade housing and the pack of replacement blades. Once the blade has been opened, we can remove the blade housing and bract from the pocketknife.

Brand sure when you lot accomplish this point yous pay attention to how the pocketknife sits in the housing. After noting this you lot tin remove the knife from the housing and dispose of it safely.

Replacing Blades

The replacement blades are usually wrapped in a little pack. They oft come in sets of between 3 and five. You volition desire to carefully remove these blades from the pocketknifehandle and so you exercise not cut yourself. Then unwrap the blades and remove ane from the parcel. Afterward yous accept a new one out, place the other blades dorsum into the handle.

Now take the new blade and seat information technology into the housing the same way the old ane came out. The blades in this pocketknife have a two notch system which needs to become placed correctly back into the housing. This creates a nice firm agree on the blade.

Putting The Box Cutter Back Together

At this point, we will desire to start reassembling the box cutter. Place the blade and housing back into the handle, ensure that the extra blades are seated properly and so place the top of the handle dorsum onto the bottom. Then fasten the screw back into place and your utility knife is as skilful equally new.

*When fastening the spiral back into place you want to brand sure to snug the screw but not over-tighten it. If you over-tighten the screw it will compress the handle and seize up the blades movement in the handle. To mitigate this, tighten then check by opening and closing the box cutter a few times to make sure information technology is at a comfy resistance to opening and endmost.

Our Thoughts

We are using a standard metal box cutter in our example but many blades piece of work in the same or a very similar fashion. Utilizing these blades will terminate up saving your visitor a fortune in the long run. Make sure you educate employees on the extra blades (if bachelor) or have an employee who can alter them readily available to alter blades out for the other employees. The type of box cutter we used, after spending virtually five minutes on it the first fourth dimension, we were able to change a blade in about two minutes. Making it significantly cheaper to accept someone alter the blades than to just buy more than.

---

Replacing a Utility Knife & Box Cutter Blade

Utility/Box Cutter Blade Replacement Transcript Coil Downwardly To Go on Reading Bob: Welcome dorsum to Albany County Fasteners – Fasteners 101. Today I want to bear witness you how to properly change a bract in a utility knife. Lets get started. So I have my utility knife here. This is but a standard utility knife. This is similar a five dollar utility pocketknife. You lot tin get more expensive utility knives, unless yous're a contractor or or one of those guys that are using information technology professionally every day, this will do. This is a very simple unit. Now I'm going to bear witness you how to modify the blade properly you lot demand a number two Phillips and we get out of my instance here. OK and i'm simply going to unscrew this Phillips screw right here. I'm gonna take that out. Remove the spiral then you simply pop this top off. This whole mechanism comes out of the utility knife, like a casing, and then in the back, typically in the back of the utility knife itself, they requite y'all a little package of additional blades. In this case they give you 4 extra ones. So you lot take the bract out of there, you have the mechanism that information technology snaps into. Then at present, there are two holes. There'due south merely one you can get information technology into alright, so two slots they see those two slots you can only get it into one and that'due south the only way volition fit. It should fit snug in in that location, yous shouldn't get a bract that is sloppy and moves around and it should just fit perfectly as I'thou showing you hither. Once you have that, you lot can simply slide this, put it back in there, simply the cardinal to this is pushing this down so it volition slide back and forth. Now when you put the elevation on, there's a lot of people running into this problem. If they don't put that in properly it won't adjust for you lot and then this is like a hinge you but snap information technology in like that. Earlier you put the spiral, when y'all start screwing it, brand sure that you have rotation; that it'due south sliding back and forth for you. Put the spiral back in, but snug the screw, don't over tighten it, I just tighten it. I but tighten information technology till information technology stopped. At that place you tin can encounter that it was free. A lot of times people over tighten this, put all their musculus into it then in this case it'southward non happening but in some utility knives it will non role properly. There you get. Thanks for watching.

Source: https://www.albanycountyfasteners.com/blog/how-to-replace-a-utility-box-cutter-knife-blade/

Share this post